Licensing - Revision history

Davo: /* License Key */

2024-09-09T19:53:53Z

‎License Key

2024-09-09T19:53:33Z

‎License Key

2024-09-09T19:53:05Z

‎License Key

2022-11-28T16:57:17Z

2022-05-24T12:16:15Z

2022-05-24T12:14:46Z

2021-02-23T18:50:40Z

2020-04-29T13:58:01Z

2020-04-29T13:47:56Z

2020-04-29T13:47:38Z

@@ Line 46: / Line 46: @@
 Go back to the Printer Settings screen and click the '''Seed>USB''' button again; you'll get a message that this seed is already found, and the KEY should be loaded and displayed in the "Firmware KEY" field. Just click the '''Flash KEY''' button, and a message should appear in the message area at the bottom of the 3D View tab stating that a valid key has been detected.
-''Note: If you are typing this in by hand from a sans-serif font, and it does not work, be sure to try lower case "L" and upper case "I" and number "1" for a character like "|".'' :)
+''Note: If you are typing this in by hand from a sans-serif font, and it does not work, be sure to try lower case "L" and upper case "i" and number "one" for a character like "|".'' :)
 [[File:Lic_hw_info_flash_key.png]]
 Your KEY is now flashed, and your motion controller is licensed to work with Repetrel version 4 (and above).

@@ Line 45: / Line 45: @@
 Go back to the Printer Settings screen and click the '''Seed>USB''' button again; you'll get a message that this seed is already found, and the KEY should be loaded and displayed in the "Firmware KEY" field. Just click the '''Flash KEY''' button, and a message should appear in the message area at the bottom of the 3D View tab stating that a valid key has been detected.
 [[File:Lic_hw_info_flash_key.png]]
 Your KEY is now flashed, and your motion controller is licensed to work with Repetrel version 4 (and above).

← Older revision		Revision as of 19:53, 9 September 2024
Line 49:		Line 49:

	Your KEY is now flashed, and your motion controller is licensed to work with Repetrel version 4 (and above).		Your KEY is now flashed, and your motion controller is licensed to work with Repetrel version 4 (and above).
		+
		+	''Note: If you are typing this in by hand from a sans-serif font, and it does not work, be sure to try lower case "L" and upper case "I" and number "1" for a character like "\|".'' :)

@@ Line 7: / Line 7: @@
 If your printer is over 24 months old and does not have a v4 license, there will be a $250 fee for your license.
-We are happy to help you get your motion controller licensed. Contact us at hyrel3d@gmail.com with any questions. Instructions are as follows.
+We are happy to help you get your '''motion controller''' licensed. Software installs '''no not''' need licenses. Install anywhere you like - but only connect to the printer from ONE install at a time. Contact us at hyrel3d@gmail.com with any questions. Instructions are as follows.
 These steps are performed in this video: https://www.youtube.com/watch?v=r7UimNDjNiY

@@ Line 16: / Line 16: @@
-== Repetrel ==
+== License Seed ==
 You must have version 4 or above installed to generate a license.
@@ Line 37: / Line 37: @@
 You will get this number to us - preferably, we will get you your license during a live support session; alternately, you can email it to us. You can copy the SEED from the screen, or click the '''Seed>USB''' button, which will write it to the first field of a new line in a text file on an attached USB drive. This file can be erased after the license is applied, but we MUST write it to a USB drive, at least temporarily.
 We will then generate a license FOR YOUR UNIT, and get it back to you. This will be a 32 digit license KEY, formatted as two groups of 15 characters, separated by two underscores. An example KEY is '''d5gh7eAsTdr71f5__k8JEz5j9df984KD'''. Note, the numbers on this page are examples, and will not work on your printer. This will be pasted in the second field of the text file on the USB drive.

← Older revision		Revision as of 12:14, 24 May 2022
Line 1:		Line 1:
		+	{\| align="right"
		+	\| __TOC__
		+	\|}
		+
	As of version 4, Repetrel will not operate your motion controller (printer) without a license.		As of version 4, Repetrel will not operate your motion controller (printer) without a license.

@@ Line 1: / Line 1: @@
 As of version 4, Repetrel will not operate your motion controller (printer) without a license.
-If your printer shipped with Repetrel version 1.x or 2.x, or if your printer shipped prior to Nov 2017, there will be a $250 fee for your license.
+If your printer is over 24 months old and does not have a v4 license, there will be a $250 fee for your license.
 We are happy to help you get your motion controller licensed. Contact us at hyrel3d@gmail.com with any questions. Instructions are as follows.

← Older revision		Revision as of 13:58, 29 April 2020
Line 11:		Line 11:
	<span style="color: red;">'''''Please note that you should ensure that your ST-Link is working before you attempt this upgrade.'''''</span>		<span style="color: red;">'''''Please note that you should ensure that your ST-Link is working before you attempt this upgrade.'''''</span>

−	<span style="color: red;">'''''Please note ~~tht~~ if you cannot perform the upgrade yourself, we charge a $100 service fee to help.'''''</span>	+	<span style="color: red;">'''''Please note that if you cannot perform the upgrade yourself, we charge a $100 service fee to help.'''''</span>

← Older revision		Revision as of 13:47, 29 April 2020
Line 8:		Line 8:

	These steps are performed in this video: https://www.youtube.com/watch?v=r7UimNDjNiY		These steps are performed in this video: https://www.youtube.com/watch?v=r7UimNDjNiY
−
−	~~<span style="color: red;">'''''Please note that version 4 and above require a license key to operate - see [[Licensing]] for details.'''''</span>~~

	<span style="color: red;">'''''Please note that you should ensure that your ST-Link is working before you attempt this upgrade.'''''</span>		<span style="color: red;">'''''Please note that you should ensure that your ST-Link is working before you attempt this upgrade.'''''</span>