Other accessories - Revision history

Davo: /* Spindle Tools */

2024-07-15T13:36:18Z

‎Spindle Tools

2021-08-16T15:08:32Z

2020-06-19T20:16:11Z

2020-06-19T20:12:48Z

‎Spindle Tools

2020-01-13T13:34:02Z

‎Other Tool Position Accessories

2019-10-07T20:43:02Z

‎Other Tool Position Accessories

2017-10-13T14:20:10Z

‎Lasers

2017-01-23T19:42:05Z

‎Non-Tool Position Accessories

2017-01-23T14:27:33Z

‎Non-Tool Position Accessories

2016-12-02T15:33:38Z

@@ Line 19: / Line 19: @@
 The ST1 is intended for light drilling and routing operations (especially circuit board work), and provides between 500 and 5,000 RMP (depending on load) to a 1/8" chuck. 12VDC, 4A, 40W.
-The ST3 is intended for light drilling and machining operations (even on brass), and provides between 2,000 and 12,000 RMP (depending on load) to a 1/48" chuck. 48VDC, 8.3A, 400W.
+The ST3 is intended for light drilling and machining operations (even on brass), and provides between 2,000 and 12,000 RMP (depending on load) to a 1/4" chuck. 48VDC, 8.3A, 400W.
 Our Repetrel software can process Gerber and DRL files for the Spindle Tool and/or the Lasers.

@@ Line 8: / Line 8: @@
 === Lasers ===
-See [[Lasers]].
+See our page for [[Lasers]].
 === Spindle Tools ===

@@ Line 5: / Line 5: @@
 Accessories other than print heads are available, some of which take a tool position.
 === Lasers ===
@@ Line 27: / Line 23: @@
 Our Repetrel software can process Gerber and DRL files for the Spindle Tool and/or the Lasers.
-== '''Other Tool Position Accessories''' ==
+=== '''Other Accessories''' ===
 The following accessories each take up a tool position while performing more ancillary functions:
@@ Line 35: / Line 31: @@
 * The Tramming Tool, provided with every printer, is used to level the build surface.
 * The Precision Tool Setter! See https://www.youtube.com/watch?v=rW7h9z5DW5A
 The following accessories are not loaded into tool positions on the yoke:

@@ Line 18: / Line 18: @@
 <gallery>
 File:ST1.png|ST1
 </gallery>
-Intended for light drilling and routing operations (especially circuit board work), the ST1 provides between 500 and 5000 RMP (depending on load) to a 1/8" chuck. Our Repetrel software can process Gerber and DRL files for the Spindle Tool and/or the Lasers.
+The ST1 is intended for light drilling and routing operations (especially circuit board work), and provides between 500 and 5,000 RMP (depending on load) to a 1/8" chuck. 12VDC, 4A, 40W.
 == '''Other Tool Position Accessories''' ==

@@ Line 29: / Line 29: @@
 * The Quiet Storm fan provides additional cooling.
 * The Tramming Tool, provided with every printer, is used to level the build surface.
 == '''Non-Tool Position Accessories''' ==

@@ Line 41: / Line 41: @@
 The following accessories are not loaded into tool positions on the yoke:
 * The Feed Chamber Cooling Fan mounts on Hot Flow heads to provide additional cooling to the feed chamber. This is desirable with low temperature filaments like PLA.
 * The Printer Support Kit is included with every printer, and includes a build plate, blue tape, and a variety of handy tools like tweezers, razors, and a spatula.
-* The SDK | Software Developer's Kit provides hardware, software, and the source code for developing your own firmware for your own compatible heads.
+* The SDK - Software Developer's Kit provides hardware, software, and the source code for developing your own firmware for your own compatible heads.
-* The LTK | Luer Tip Kit provides an EMO to Luer adapter and a variety of luer lock needles.
+* The LTK - Luer Tip Kit provides an EMO to Luer adapter and a variety of luer lock needles.
 * The Syringe Kit provides syringes in quantity.
 * The Drill Bit Kit provides an assortment of drilling bits and end mills for the Spindle Tool.
 * The Filament Kit provides a variety of filaments to get you started with your printer.

← Older revision		Revision as of 14:27, 23 January 2017
Line 48:		Line 48:
	* The Drill Bit Kit provides an assortment of drilling bits and end mills for the Spindle Tool.		* The Drill Bit Kit provides an assortment of drilling bits and end mills for the Spindle Tool.
	* The Filament Kit provides a variety of filaments to get you started with your printer.		* The Filament Kit provides a variety of filaments to get you started with your printer.
		+	* The Enclosure Heater with Temperature Control (HTC) is avialable in 120 and 240 VAC versions. [[:File:Htc.jpg\|Spec Sheet]]

@@ Line 3: / Line 3: @@
 | __TOC__
 |}
 == '''Tool Position Accessories''' ==
 === Lasers ===
@@ Line 27: / Line 31: @@
 == '''Other Tool Position Accessories''' ==
-The following accessories each take up a tool position while performing more passive functions:
+The following accessories each take up a tool position while performing more ancillary functions:
 * The Inspector microscope provides magnification.
@@ Line 35: / Line 39: @@
 == '''Non-Tool Position Accessories''' ==
-The following non-head accessories are also available:
+The following accessories are not loaded into tool positions on the yoke:
 * The Feed Chamber Cooling Fan mounts on Hot Flow heads to provide additional cooling to the feed chamber. This is desirable with low temperature filaments like PLA.